Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultrason® E 2010 MR SW 10111 - PESU - BASF

Material Data Center offers the following functions for Ultrason® E 2010 MR SW 10111:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultrason E datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 70 cm³/10min ISO 1133
Temperatura 360 °C -
Carga 10 kg -
Contracción posterior al moldeo, paralelo 0.8 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.9 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 2650 MPa ISO 527
Esfuerzo de fluencia 85 MPa ISO 527
Alarg. en límite elástico 6.9 % ISO 527
Módulo de plastodeformación, 1000h 2700 MPa ISO 899-1
Resistencia al impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 6.5 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 7 kJ/m² ISO 179/1eA
Resistencia al impacto Izod con entalla, +23°C 6.5 kJ/m² ISO 180/1A
Resistencia al impacto Izod con entalla 7 kJ/m² ISO 180/1A
Temperatura -30 °C -
Ball indentation hardness 154 MPa ISO 2039-1
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temp. de transición vítrea, 10°C/min 225 °C ISO 11357-1/-2
Estabilidad al calor, 1.80 MPa 205 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 52 E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espesores de probeta 1.6 mm -
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 3.0 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 100Hz 3.9 - IEC 62631-2-1
Constante dieléctrica, 1MHz 3.8 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 100Hz 17 E-4 IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 140 E-4 IEC 62631-2-1
Resistividad volumétrica específica >1E13 Ohm*m IEC 62631-3-1
Resistencia dieléctrica 37 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 100 - IEC 60112
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 2.2 % Sim. to ISO 62
Absorción de humedad 0.8 % Sim. to ISO 62
Densidad 1370 kg/m³ ISO 1183
Propiedades específicas del materialValorUnidadesMétodo de ensayo
ISO Data
Indice de viscosidad 56 cm³/g ISO 307, 1157, 1628
Características
Procesamiento y forma de entrega
Moldeo por inyección, Otros tipos de extrusión, Moldeo por soplado
Forma de suministro
Sémola, Negro
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.